Boss Audio Systems Musical Toy Instrument BCB 60 User Manual

How to Connect  
Owner’s Manual  
*
To prevent malfunction and/or damage to speakers or other devices, always turn down the  
volume, and turn off the power on all devices before making any connections.  
Example of Connection Setup Incorporating a Wah Pedal  
Remove the right panel, then use a Phillips head screwdriver to remove the two  
screws securing the wire holder under the right panel.  
Thank you, and congratulations on your choice of the BOSS BCB-60 Pedal Board.  
Main Features  
New Way to Secure Effects Pedals Works with All Types of Pedals,  
Lets You Arrange Them However You Like  
Before using this unit, carefully read the sections entitled: “USING THE UNIT  
SAFELY” and “IMPORTANT NOTES.”  
*
Once the connections have been completed, turn on power to your various devices in the  
order specified. By turning on devices in the wrong order, you risk causing malfunction  
and/or damage to speakers and other devices.  
These sections provide important information concerning the proper operation of  
the unit. Additionally, in order to feel assured that you have gained a good grasp of  
every feature provided by your new unit, this manual should be read in its entirety.  
The manual should be saved and kept on hand as a convenient reference.  
Thumbscrews  
Now you can set up compact pedals as well as twin pedals simply and easily with  
holding pads; the pedal shapes are described in dotted lines right on the pads. These  
pads allow you to pull off and rearrange your pedals in seconds, without the need  
for double-sided tape. In addition, the BCB-60 comes with an unshaped holding pad  
blank, which you can cut to any desired shape, allowing you to use a wide variety of  
pedals.  
When powering up:  
When powering down:  
Turn on the power to your guitar amp last.  
Turn off the power to your guitar amp first.  
Screws  
1. Connect your amps and guitar as shown in the figure.  
Copyright © 2003 BOSS CORPORATION  
All rights reserved. No part of this publication may be reproduced in any form  
without the written permission of BOSS CORPORATION.  
Power Supply Function  
The BCB-60 comes with a high-capacity 1000-mA AC adaptor with five times the  
capacity of PSA-series adaptors, providing ample power for all of the effects pedals  
connected to the BCB-60.  
Attach the wah pedal as shown in the figure. Set the wah pedal’s rubber feet in the  
depressions.  
Super-Tough Blow-Molded Body  
.........................................................................................................................................................................................................................................................................................................................................................................................................................................................  
Panel Descriptions  
2. Remove the thumbscrews, and remove the left and right panels.  
Thumbscrews  
11  
5
6
Ground  
Terminal  
1
1
2
3
7
4
12  
8
3. Use the LL cables to connect your effects pedals and tuner.  
Cut the holding pad to the shape of the pedal to be attached.  
9
LL Cable (5-1/8”)  
*
Exercise care when using cutting tools so as to avoid injury as you shape the holding pads.  
LL Cable (15-3/4”)  
Main Specifications  
Spare Holding Pad  
Connectors:  
INPUT Jack (1/4” phone type)  
SEND Jack (1/4” phone type)  
RETURN A/B Jacks (1/4” phone type)  
OUTPUT A/B Jacks (1/4” phone type)  
PSC IN Jack, DC OUT Jack  
Power Supply:  
Dimensions:  
DC 9 V: AC Adaptor (PSC series)  
670 (W) x 370 (D) x 100 (H) mm  
10  
10  
26-7/16 (W) x 14-5/8 (D) x 3-15/16 inches  
3.8 kg / 8 lbs 7 oz  
Weight:  
4. Connect the effects pedals with the 8pin parallel DC cable.  
1. Free Pockets  
Use these for your AC adaptor, tuner, and other small items.  
8. Wire Holder  
The LL and 8pin parallel DC cables are secured in these spaces.  
Accessories:  
AC Adaptor (PSC series) 9 V, 1000 mA x 1  
8-pin Parallel DC Cable x 1  
Connect the L-shaped plug to DC OUT.  
On both sides, the recessed spaces feature suitably sized gaps, making it easy to pull  
out just the cable you want.  
LL Cable (1/4” L-shaped 1/4” L-shaped; 5-1/8”) x 5  
LL Cable (1/4” L-shaped 1/4” L-shaped; 15-3/4”) x 3  
Spare Holding Pad x 1  
2. INPUT  
Connect your guitar cable here.  
9. Holding Pads  
These pads are used to keep your effects firmly in place.  
3. SEND  
Owner’s Manual (This sheet)  
Connect the input of the first effects pedal to be connected here.  
Use the included LL cable for this connection.  
These pads can be attached and removed easily with the attachment screws at the  
pads’ four corners.  
*
In the interest of product improvement, the specifications and/or appearance of this unit  
are subject to change without prior notice.  
Setting up BOSS compact pedals and twin pedals is easy—just cut along the dotted  
lines and remove the excess material.  
4. RETURN A/B  
Connect the input of the effects pedal  
To accommodate an effects pedal that has an unusual shape, use the provided  
unshaped pad blank, and cut it to match the shape of the pedal. This allows you to  
get a perfectly formed pad, even for a differently shaped pedal.  
5. OUTPUT A/B  
Connect your guitar amp here.  
(Signals input to RETURN A are output from OUTPUT A; signals input to RETURN  
B are output from OUTPUT B.)  
*
Exercise care when using cutting tools so as to avoid injury as you shape the holding pads.  
5. Attach the left and right panels using the thumbscrews removed in step 2.  
10. Left Panel/Right Panel  
These plates are used to hide the cables in the wire holder.  
*
The BCB-60 includes the two return and output pairs, A and B, for compatibility with  
stereo output effects. Use either A or B if your effects pedal's output is mono.  
Examples of Compact Pedal and Twin Pedal Connections  
Secure the panels to the wire holder with the thumbscrews.  
6. PSC IN  
11. PSC Adaptor  
Connect the included PSC adaptor here.  
This is a specialized power adaptor for the BCB-60.  
*
Do not connect the PSC adaptor directly to the effects pedals.  
Connect the L-shaped DC plug to PSC IN.  
7. DC OUT  
12. 8Pin Parallel DC Cable  
Connect the L-shaped DC plug to DC OUT and other plugs to any effects pedal you  
want to connect.  
This is the power supply connector for your effects pedals.  
Accepts connection of the included 8pin parallel DC cable.  
You can connect only effects pedals compatible with BOSS PSA and ACA adaptors.  
*
When using effects pedals compatible with the BOSS ACA adaptor, be sure to route the  
guitar signal via the BCB-60’s send and returns. Insufficient voltage is supplied to the  
effects pedals unless the signal is routed through the send and returns.  
Always put the supplied tubes on the plugs and keep them in the wire holder when  
not in use.  
 

Belkin Network Card Network Adapror User Manual
Black Box Computer Hardware HDMCII VDSL2 LAN Extender Module Extended Temp User Manual
Black Decker Grinder G950 User Manual
Black Decker Welder VP650 User Manual
Bolens Personal Computer P5S800 VM User Manual
Bravetti Toaster TO283H User Manual
Bushnell Binoculars 98 0917 04 09 User Manual
Bushnell Laser Level 201042 User Manual
Carrier Heat Pump 50RLP User Manual
CDA Oven SV 210 User Manual