Kawai Musical Instrument CP67 User Manual

Digital Piano  
CP67  
Owner’s Manual  
 
Important Safety Instructions  
SAVE THESE INSTRUCTIONS  
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS  
WARNING  
TO REDUCE THE RISK OF  
CAUTION  
FIRE  
OR  
ELECTRIC  
SHOCK, DO NOT EXPOSE  
THIS PRODUCT TO RAIN  
OR MOISTURE.  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
AVIS : RISQUE DE CHOC ELECTRIQUE  
- NE PAS OUVRIR.  
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).  
NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.  
The lighting flash with arrowhead symbol, within  
The exclamation point within an equilateral triangle  
is intended to alert the user to the presence of  
important operating and maintenance (servicing)  
instructions in the leterature accompanying the  
product.  
an equilateral triangle, is intended to alert the user  
to the presence of uninsulated "dangerous voltage"  
within the product's enclosure that may be of  
sufficient magnitude to constitute a risk of electric  
shock to persons.  
Examples of Picture Symbols  
denotes that care should be taken.  
The example instructs the user to take care not to allow fingers to be trapped.  
denotes a prohibited operation.  
The example instructs that disassembly of the product is prohibited.  
denotes an operation that should be carried out.  
The example instructs the user to remove the power cord plug from the AC outlet.  
Read all the instructions before using the product.  
WARNING - When using electric products, basic precautions should always be followed,  
including the following.  
Indicates a potential hazard that could result in death  
WARNING or serious injury if the product is handled incorrectly.  
The product should be connected to  
an AC outlet of the specified  
voltage.  
If you are going to use an AC power cord,  
make sure that its has the correct plug shape  
and conforms to the specified power voltage.  
Failure to do so may result in fire.  
120V  
230V  
240V  
Do not insert or disconnect the power  
cord plug with wet hands.  
Doing so may cause electric shock.  
The chair must be used properly(it must be  
used only when playing the product).  
Doing so may cause the chair to fall over or your  
fingers to be trapped, resulting in injury.  
Do not play with it or stand on it.  
Only one person is allowed to sit on it.  
Do not sit on it when opening the lid.  
When using the headphones, do not  
listen for long periods of  
time at high volume levels.  
Doing so may result in hearing problems.  
– 3 –  
 
Do not lean against the keyboard.  
Doing so may cause the product to fall over,  
resulting in injury.  
Do not disassemble, repair or modify  
the product.  
Doing somayresult in product breakdown,electric  
shock or short-circuit.  
Pulling the AC power cord itself may damage  
the cord, causing a fire, electric shock or  
short-circuit.  
WhendisconnectingtheACpowercord's  
plug, always hold the plug  
and pull it to remove it.  
The product is not completely disconnected from the  
power supply even when the power switch is turned  
off. If the product will not be used for a long time,  
unplug the AC power cord from the AC outlet.  
Failure to do so may cause fire in case of  
lightning.  
Failure to do so may over-heat the product,  
resulting in fire.  
This product may be equipped with a polarized line plug (one blade  
wider than the other). This is a safety feature.  
If you are unable to insert the plug into the outlet, contact an  
electrician to replace your obsolete outlet.  
Do not defeat the safety purpose of the plug.  
Indicates a potential hazard that could result in injury  
or damage to the product or other  
CAUTION  
Do not use the product in the following areas.  
Using the product in such areas may result in  
product breakdown.  
Areas, such as those near windows, where the product is  
exposed to direct sunlight  
Extremely hot areas, such as near a heater  
Extremely cold areas, such as outside  
Extremely humid areas  
Areas where a large amount of sand or dust is present  
Areas where the product is exposed to excessive  
vibrations  
When you close the keyboard cover,  
close it gently.  
Closing it roughly may trap your fingers, resulting  
in injury.  
OFF  
Before connecting cords, make sure  
that the power to this product  
and other devices is turned  
OFF.  
Failure to do so may cause breakdown of this  
product and other devices.  
Take care not to allow any foreign  
matter to enter the product.  
Entry of water, needles or hair pins may result  
in breakdown or short-circuit.  
The product shall not be exposed to dripping or  
splashing. No objects filled with liquids, such as  
vases, shall be placed on the product.  
Please lift up the product when moving it.  
Please note that the product is heavy and must  
be carried by more than two persons.  
Do not drag the product on the floor.  
Take care not to drop the product.  
Dropping the product may result in breakdown.  
Doing so may cause the product to generate  
Donot placethe product near electrical  
appliances such as TVs and  
radios.  
noise.  
If the product generates noise, move the  
product sufficiently away from the electrical  
appliance or connect it to another AC outlet.  
When connecting the AC power cord  
and other cords, take care  
not to get them tangled.  
Failure to do so may damage them, resulting in  
fire, electric shock or short-circuit.  
– 4 –  
 
Doing so may result in discoloration or deformation  
Do not wipe the product with benzene  
or thinner.  
of the product.  
When cleaning the product, put a soft cloth in  
lukewarm water, squeeze it well,then wipe the  
product.  
Doing so may cause the product to become  
deformed or fall over, resulting in breakdown  
or injury.  
Do not stand on the product or exert  
excessive force.  
The product should be located so that its location or position does not interfere with its proper  
ventilation.  
This product should be used only with the stand that is provided by the manufacturer.  
The product should be serviced by qualified service personnel when:  
The power supply cord or the plug has been damaged.  
Objects have fallen, or liquid has been spilled into the product.  
The product has been exposed to rain.  
The product does not appear to operate normally or exhibits a marked change in  
performance.  
The product has been dropped, or the enclosure damaged.  
Notes on Repair  
Should an abnormality occur in the product, immediately turn the power OFF, disconnect the  
power cord plug, and then contact the shop from which the product was purchased.  
CAUTION:  
To prevent electric shock, match wide blade of plug to wide slot, fully insert.  
ATTENTION:  
Pour viter les chocs lectriques, introduire la lame la plus large de la fiche dans la borne  
correspondante de la prise et pousser jusqu’au fond.  
Instruction for AC power cord (U.K.)  
Do not plug either terminal of the power cord to the ground of the AC outlet on the wall.  
FCC Information  
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the  
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential  
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in  
accordance with the instructions, may cause harmful interference to radio communications.  
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the  
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  
¥ Reorient or relocate the receiving antenna.  
¥ Increase the separation between the equipment and receiver.  
¥ Connect the equipment into an outlet on a different electrical circuit from the receiver.  
¥ Consult the dealer or an experienced radio/TV technician for help.  
Canadian Radio Interference Regulations  
This instrument complies with the limits for a class B digital apparatus, pursuant to the Radio Interference  
Regulations, C.R.C., c. 1374.  
– 5 –  
 
ASSEMBLING THE STAND  
Be sure that all parts are included before starting to assemble your unit.  
PARTS PROVIDED  
Side Panel (A)  
Back Board (B)  
2 pcs.  
1 pc.  
ø4 x 16  
ø4 x 25  
Adjuster Cord Clamp  
M6 x 25  
Pedal Board (C)  
Screw (D) (M6 x 25)  
Screw (E) (ø4 x 16)  
Screw (F) (ø4 x 25)  
Adjuster (G)  
1 pc.  
4 pcs.  
6 pcs.  
2 pcs.  
1 pc.  
1 pc.  
1 set.  
(F)  
(D)  
(E)  
(G)  
(H)  
Cord Clamp (H)  
Headphone Hook Set  
1. Insert the Adjuster (G) on the Pedal Unit.  
(A)  
2. Untie the pedal cable on the bottom of the  
Pedal Board (C).  
(a)  
(C)  
(E)  
(b)  
3. Slide the metal bracket located at the end  
of Pedal Board (C) on to screws (a) and (b)  
of Side Panel (A). Install tighten screw (E)  
then tighten screws (a) and (b). Repeat this  
procedure on the other end of the Pedal Board,  
then raise the completed stand assembly.  
(A)  
4. Fasten Side Panel (A) and Back Panel (B)  
with two screws (F). Then fix Back Panel  
(B) to Pedal Board (C) with four screws (D).  
(F)  
(C)  
CAUTION:  
To prevent personal injury, do not handle  
the main unit from the ends.  
(E)  
(B)  
5. The next step requires one person on each end of  
the main unit. Grasp the unit with both hands, one  
under the front, the other under the rear (remember,  
not the end) and carefully center the main unit on  
top of the stand so that the hook brackets located  
on the bottom rear of the main unit are inside the  
stand side panels (A) and approximately one-third  
of the rear, top edge of the side panels are exposed.  
(See the illustration to the right)  
(D)  
(A)  
– 6 –  
 
6. Maintaining a firm grasp under the front of the main, unit  
slide it toward the rear of the stand until the hook brackets engage  
the brackets at the rear top of the side panels (A). This hook  
arrangement is design to prevent the main unit from tilting  
forward while the screws are installed. Keep one hand under  
the front of the main unit, push down on the front to be certain  
that hooks are properly engaged.  
7. Fasten the main unit and the stand with four screws (D).  
CAUTION:  
Be sure to secure the main unit to the stand with the screws.  
If you fail to do so, the unit could fall from the stand causing  
damage or personal injury.  
8. Insert the pedal connection cord that comes  
from Pedal Board (C) into the pianos pedal jack  
and fasten with cord clamps.  
(H)  
9. Turn the adjuster (installed on the bottom of  
the Pedal Unit) down until it makes firm contact  
with the floor. If the floor is carpeted, place a  
spiked furniture cup under the adjuster so that it  
makes firm contact with the carpet backing.  
Press any pedal with your foot. If the pedal rail  
flexes, lower the adjuster until flexing is  
minimized.  
Bottom View  
CAUTION:  
Before moving your piano, turn the adjuster  
up so that it clears the floor.  
Attaching The Headphone Hook (Option)  
Fix the headphone hook to the bottom of the piano with two screws packed in the same plastic bag.  
– 7 –  
 
PART NAMES  
MASTER VOLUME SLIDER (A)  
Move the volume slider to the right to increase the instruments volume. Move the slider to the left  
to decrease the volume.  
CONCERT MAGIC BUTTON (B)  
This button is used to listen to a Concert Magic song.  
DEMO BUTTON (C)  
To listen to the demos, simply press this button and the demos will start.  
STYLE BUTTONS (D)  
These buttons are used to select different styles to accompany your playing.  
1-2 PLAY BUTTON (E)  
This button is used to automatically choose an appropriate sound and setup for the selected style.  
METRONOME BUTTONS (F)  
This button is used to start/stop the metronome.  
ACC BUTTON (G)  
This button is used to turn the auto accompaniment style function on/off.  
SYNC BUTTON (H)  
When active, the accompaniment style will start as soon as you play a note or chord on the keyboard.  
START/STOP BUTTON (I)  
This button is used to start and stop the accompaniment style.  
INTRO/ENDING BUTTON (J)  
This button is used to play an intro section that leads into the style. If you press this button while  
the style is playing an ending section will be played before stopping.  
FILL IN BUTTON (K)  
This button is used to play a short fill in section that embellishes the style and leads to the next  
section.  
FRONT PANEL  
K
E
F
G H  
I J  
B C  
D
A
8 –  
 
VALUE BUTTONS (L)  
This buttons are used to adjust tempo, scroll through different selections, and adjust data values on  
the LED display.  
EFFECTS BUTTON (M)  
This button turns the Effect on/off.  
REVERB BUTTON (N)  
This button turns the Reverb on/off.  
BALANCE SLIDER (O)  
This slider adjusts the volume balance of the two sounds used in Dual mode.  
Also adjusts the volume of the accompaniment style.  
SOUND BUTTONS (P)  
These buttons are used to select the desired sound.  
RECORDER BUTTONS (Q)  
The PLAY/STOP button is used to play back and stop a recorded song.  
The REC button is used to start recording a song.  
You can record and play back up to three songs.  
FUNCTION BUTTONS (R)  
These buttons are used to select a touch type, transpose the keyboard, and control other features  
(including MIDI functions).  
Q
P
R
L M  
N
O
9 –  
 
POWER BUTTON (a)  
This button turns the instrument on and off. Be sure to turn off the instrument when you are  
finished playing.  
a
SOFT PEDAL (b)  
Depressing this pedal softens the sound and also reduces its volume.  
SOSTENUTO PEDAL (c)  
Depressing this pedal after playing the keyboard and before releasing the keys sustains the sound  
of only the keys just played.  
SUSTAIN PEDAL (d)  
Depressing this pedal sustains the sound even after you remove your hands from the keyboard.  
b
c
d
10 –  
 
LINE OUT JACKS (e)  
These jacks are used to connect an external amplifier and speakers, or a cassette recorder to the CP  
piano.  
LINE IN JACKS (f)  
These jacks are used to connect stereo outputs from other audio equipment or electronic instruments  
to the CP pianos speakers.  
MIDI JACKS (g)  
These jacks are used to connect the CP piano with external MIDI devices.  
PEDAL JACK (h)  
Connect the pedal cord from the pedal board to this jack.  
HEADPHONES JACKS (i)  
These jacks are used to connect up to two headphones to the CP67.  
BOTTOM  
/
g
e
h
f
i
11 –  
 
GETTING STARTED  
1. BASIC OPERATIONS  
(1) Turn on the power.  
You will find the POWER SWITCH at the right end of the front panel.  
Press this button to turn on the power. Pressing it again will turn off the  
power.  
(2) Adjust the volume.  
Play a note on the keyboard and adjust the volume (Moving the slider to  
the right raises the volume while moving to the left lowers it.)  
(3) Select a sound.  
Press the SOUND SELECT button under the name of the instrument  
you would like to listen to. When the button is pressed, the LED indicator  
will be turned on to indicate that this sound is selected. The SOUND  
SELECT buttons are assigned with three preset sounds to select. To select  
the other sounds, press the button repeatedly. When a SOUND  
SELECT button is pressed, the variation number is briefly shown in the  
display. Pressing the same SOUND SELECT button again will select the  
next variation sound assigned to the SOUND SELECT button.  
You can also select any preset sounds by using the VALUE buttons while  
the variation number is shown on the LED display.  
(4) Play.  
Experiment by playing the different sounds.  
(5) Dual  
Another feature of the CP piano is the ability to layer two preset sounds  
together to create a more complex sound. For example, piano layered  
with strings, e. piano with brass sound, and so on.  
To layer two sounds, select the first sound and then, while holding down  
that SOUND SELECT button, select the second sound by pressing  
another SOUND SELECT button. The LED indicators for each will be  
turned on to indicate the two sounds you have chosen. The display briefly  
shows the combination of the selected sound variation numbers.  
You can adjust the volume balance between the two sounds. Use the  
Balance slider to adjust the balance. Move the slider to the right to  
increase the volume of the rightmost preset sound and decrease the volume  
of the leftmost preset sound. The balance changes in the opposite way  
when the slider is moved to the left.  
– 12 –  
 
ABOUT POLYPHONY  
The CP piano is capable of playing up to 96 notes simultaneously (96-note  
polyphony). When playing in dual mode or when playing the stereo piano  
sound, the polyphony will be reduced by half since the piano has to produce  
two sounds for each note.  
(6) Reverb  
-REVERB adds reverberation to the sound simulating the acoustic  
environment of a recital room or concert hall.  
There are six types of reverb in the CP67. They are Small Room, Medium  
Room, Large Room, Medium Hall, Large Hall and Plate.  
To add reverb to the sound, press the REVERB button. The LED  
indicator will be turned on. If you hold down the REVERB button for  
few seconds, the current setting will be shown in the display.  
To change the reverb type, use the VALUE buttons while holding down  
the REVERB button.  
The reverb is “ON” when the LED of the REVERB button is lit.  
Pressing the REVERB button once again turns the reverb “OFF”.  
When the power is turned on, the reverb function is automatically activated.  
Large Hall  
Plate  
Medium Hall  
Large Room  
Small Room Medium Room  
(7) Effects  
-Adding an effect to the sound enhances tonal quality and improves  
acoustical realism.  
There are twelve types of effect in the CP67. They are Chorus 1, Chorus  
2, Chorus 3, Chorus 4, FB Chorus, Tremolo, Rotary 1, Rotary 2, Flanger,  
Delay 1, Delay 2 and Delay 3.  
To add an effect to the sound, press the EFFECTS button. The LED  
indicator will be turned on and the LED display will show you which  
effect is currently selected.  
To change the effect type, use the VALUE buttons while holding down  
the EFFECTS button.  
Pressing the EFFECTS button once again turns the effect “OFF”.  
FB Chorus  
Chorus 4  
Tremolo  
Rotary 2  
Flanger  
Delay 3  
– 13 –  
 
2. STYLE  
(1) Select a style.  
Press one of the STYLE buttons. The LED of the selected STYLE button  
will light to indicate which style is currently in being used. Pressing the  
active STYLE button again will switch to the alternative style of the STYLE  
button.  
(2) Start the style.  
Pressing the START/STOP button will start the style. Pressing it again  
will stop the style.  
Pressing the INTRO/ENDING button will start the style with an intro  
section. Pressing it again will stop the style with an ending section.  
Pressing the FILL IN button while the style is running will play a short fill  
in section which embellishes the style and leads to the next variation section.  
When the SYNC button is pressed, the style will not start until you play a  
note or chord on the keyboard.  
(3) Adjust the Tempo.  
You can adjust the tempo by using the VALUE buttons. The tempo is  
shown in the LED display when the style is running . If the tempo is not  
shown in the LED display, touching the VALUE buttons will activate the  
LED display to show the tempo.  
(4) Turn on the accompaniment.  
When the ACC button is pressed, the CP piano will play a complete  
accompaniment style. In addition, the keyboard will be split into two  
sections-upper and lower keyboard. When the ACC button is turned OFF  
only the rhythm accompaniment will be played. With the ACC button  
ON, when you play a chord in the lower keyboard the accompaniment  
style will automatically follow the chords you play. The accompaniment  
system is capable of following single finger as well as more complex chord  
voicings. If you want to change the volume for the style, use the Balance  
slider while holding down the ACC button. The LED display shows  
you the volume level for the style from 0 (soft) to 127 (loud). If you want  
to change the split point for the lower keyboard, press a key on the  
keyboard while holding down theACC button. The pressed key will be  
the lowest note for the upper keyboard.  
– 14 –  
 
(5) 1-2 Play mode  
When the 1-2 PLAY button is activated, the CP piano will automatically  
choose an appropriate sound setup and tempo for the selected style.  
You can adjust the volume of the accompaniment style by using Balance  
slider.  
3. TRANSPOSE  
The transpose function lets you raise or lower the piano’s key in half steps.  
This is especially useful when you have learned a song in one key and  
have to play it in another key. The transpose feature allows you to play the  
song in the original key, but hear it in another key.  
To transpose the keyboard, press and hold the TRANSPOSE button.  
The LED display shows you the current value. The value is always set to  
“0” when the power is turned on.  
Value: 0  
Value: -5  
While still holding the TRANSPOSE button, use the VALUE buttons  
or the keyboard from C2 to C4 to specify the transposition amount.  
The LED display shows you a number telling you how many half steps up  
or down you have transposed the piano. -5, for example, represents a  
transposition that is 5 half steps lower. “0” indicates no transposition.  
The piano can be transposed up to 12 half steps higher or 12 half steps  
lower.  
Pressing TRANSPOSE button again turns the transpose function off.  
The TRANSPOSE function remembers the current setting as long as the  
power is on.  
4. TOUCH RESPONSE  
When playing a piano, the volume of the sound produced increases in  
direct relation to how hard a key is struck. The CPpiano offers the realistic  
feel of an acoustic piano for practicing music. The touch response function  
simulates the standard touch of an acoustic piano when the LED of the  
TOUCH button is off. When the LED of the TOUCH button is lit, you can  
select other touch types as follows.  
Light 1 / 2 (Lt):  
For those still developing finger strength, such as a  
child, a louder sound is produced even when the piano  
is played with a soft touch. Light 2 is lighter than  
Light 1.  
LIGHT 1  
– 15 –  
 
Heavy 1 / 2 (HE):  
Perfect for those with strong fingers or for practicing  
with a hard touch. Heavy 2 is heavier than Heavy 1.  
HEAVY 2  
OFF  
Off (OFF):  
For tone colors like organ or harpsichord, and for  
playing some contemporary music with the piano  
sound, a constant loud sound is produced regardless  
of your force on the keys.  
To change the touch type, press and hold the TOUCH button. The  
LED display shows you the current touch type. While holding the TOUCH  
button, use the VALUE buttons to change the touch type.  
Press the TOUCH button again to get back to the standard touch  
setting.  
Once the power is turned off, the touch type will be reset to the standard  
setting.  
5. DEMONSTRATION SONG  
The CP piano has 3 built in demonstration songs for your listening  
enjoyment.  
Press the DEMO button and the first demo song will start. The LED  
display shows the demo song number. When the first demo song is finished,  
the CP piano will play all the other demo songs one at a time in order.  
If you would like to listen to a particular demo song, use the VALUE  
buttons to select your desired song.  
To stop the demo, press the DEMO button again at any time.  
6.METRONOME  
Rhythm is one of the most important elements when learning music. It is  
important to practice playing the piano in the right tempo and with a steady  
rhythm. The CP piano’s metronome is a tool that helps you to achieve this  
by providing a steady beat for you play along with.  
Starting the Metronome  
Press the TEMPO button. You will see the LED display turns on and  
hear the metronome begin counting with a steady beat. The display shows  
the tempo in beats per minute  
To change the tempo, use the VALUE buttons to increase or decrease  
the tempo within the range of 30-250 beats per minute. (60-500 BPM  
with 6/8).  
To stop the metronome, press the TEMPO button again.  
– 16 –  
 
Changing the time signature  
You probably noticed that there are two types of clicks and the louder one  
comes every fourth beat. The metronome is capable of giving you a down  
beat to indicate the beginning of the measure. You are now hearing a 4-  
beat or 4/4 time signature.  
You can select different a time signature if you want to out of the seven  
available with the CP piano—1/4, 2/4, 3/4, 4/4, 5/4, and 6/8.  
To change the time signature, use the BEAT button.  
Press the BEAT button. You will see the LED indicator turn on and  
hear the metronome begin counting. The display shows the time signature.  
Use the VALUE buttons to select your desired time signature.  
You will see the time signature currently selected in the display.  
To stop the metronome, press the BEAT button again.  
You can use either the TEMPO or BEAT button to turn the metronome on  
and off. Choose the appropriate button depending on whether you’re  
adjusting the tempo or changing the time signature.  
Adjusting the Metronome Volume  
The volume level of metronome can be adjusted to any level you like  
independent of the main volume.  
Press the TEMPO and BEAT buttons simultaneously. The display  
shows the volume level of the metronome in numbers from 1 (soft) to 10  
(loud). The factory preset is 5.  
Use the VALUE buttons to change value.  
– 17 –  
 
DIGITAL RECORDING FUNCTIONS  
1. EASY RECORDING  
Press the REC button. The CP piano is now ready to record. To cancel  
the recording, press the REC button again.  
Begin playing some music on the piano. The CPpiano will automatically  
start recording with the first note you play. You can also start recording by  
pressing the PLAY/STOP button.  
Press the PLAY/STOP button when you have finished recording.  
NOTE:  
Starting another recording will delete the song you previously recorded.  
2. PLAYING BACK A SONG  
Press the PLAY/STOP button. The song will be played back using the  
same tone (sound) with which it was recorded.  
Press the PLAY/STOP button once again to stop the playback. If you  
do not press the PLAY/STOPbutton, playback will automatically stop when  
the song is finished.  
You can adjust the tempo of playback by using the VALUE buttons.  
3. ADVANCED RECORDING/PLAYBACK FUNCTIONS  
RECORDING MORE SONGS  
The CP piano can record and store a maximum of 3 songs. Please follow  
the steps below to save your songs:  
While holding down the REC button, press the Song 2 button.  
The LED will blink to show the current song number (while the REC button  
is held down). The piano is now ready to record (Song 2). To cancel  
without recording, press the REC button again.  
Play the piano. Playing the piano will automatically start the recording.  
You can also start recording by pressing the PLAY/STOP button.  
– 18 –  
 
Press the PLAY/STOP button after you have finished recording.  
Holding down the PLAY/STOP button, press the SONG 2 button.  
Releasing both buttons will play Song No.2. Playback will automatically  
stop when the song is finished. You can adjust the tempo of playback  
by using the VALUE buttons.  
RECORDING/PLAYING BACK THE LEFT AND RIGHT HAND PARTS  
SEPARATELY  
The CP piano can record the parts played by the left or right hand and play  
back these parts separately or simultaneously. This function can be enjoyed  
in different ways. For example, you can practice the right-hand part of the  
song while playing back the recorded left-hand part, or record the melody  
part of the song while playing back the previously recorded accompaniment.  
While holding down the REC button, press the SONG 3 button to  
select Song No.3. Track 1 of Song No.3 will be selected and the CP piano  
is now ready to record. To cancel without recording, press the REC  
button again.  
Play the piano with your left hand. Playing the piano will automatically  
start the recording. You can also start recording by pressing the PLAY/  
STOP button.  
Press the PLAY/STOP button after you have finished recording.  
Now, to play back the left-hand part, press the PLAY/STOP button.  
The left-hand part you have recorded (Track 1 of Song No.3) will be played  
back. You can practice the right-hand part along with the recorded part.  
You can adjust the tempo of playback by using the VALUE buttons.  
Let’s record the right-hand part while listening to the left-hand part.  
While holding down the REC button, press the TRACK 2 button. The  
Track 1 LED will light and the Track 2 LED will flash to indicate that the  
piano is now ready to record Track 2. To cancel without recording, press  
the REC switch again.  
Now play the right-hand part. Pressing any key will start play back of  
the recorded left-hand part (Track 1) while you play (and record) the  
right-hand part. You can also start recording by pressing the PLAY/  
STOPbutton. After pressing the PLAY/STOPbutton the left-hand part  
will begin playing back, you can then begin playing (recording) the  
right hand part from any point in the song you like.  
Press the PLAY/STOP button after you have finished recording.  
– 19 –  
 
NOTE:  
If you play with the style (rhythm and accompaniment), it is also recorded  
but only on track 1.  
PLAYING BACK THE LEFT- AND RIGHT-HAND PARTS SEPARATELY  
After you have recorded the left- and right-hand parts (Track 1 and Track  
2) separately, it is possible to play back the two parts by themselves or  
together. The following example shows how to play back only Track 2.  
Select and press one of the SONG buttons (Song 1, Song 2 or Song 3)  
while pressing the PLAY/STOP button.  
While holding down the PLAY/STOP button, press the TRACK 1  
button.  
The TRACK 1 button LED will be turned “off”. If you need to turn Track  
1 back “on”, press the TRACK 1 button once again.  
Releasing both buttons will play back only Track 2. You can adjust  
the tempo of playback by using the VALUE buttons.  
4. DELETING A SONG/TRACK  
This function allows you to delete songs that were not recorded correctly  
or songs that you do not want to listen to any more.  
Simultaneously hold down the PLAY/STOP and REC buttons.  
The LEDs will light to show you where songs have been recorded.  
While holding down both the PLAY/STOP and REC buttons, press  
the SONG button that corresponds to the song you want to delete.  
While still holding down both the PLAY/STOPand REC buttons, press  
the TRACK button that you want to delete and turn the LED of that  
TRACK button off.  
To delete more than one song, repeat the above procedure.  
NOTE:  
– The total memory capacity of the recorder is approximately 7,000 notes.  
When the recorder reaches its maximum capacity, the CP piano will stop  
recording at this point. Any data recorded before the interruption will be  
retained.  
– To delete all recorded songs (reset), first turn the power off and then  
turn it back on again while holding down both the PLAY/STOP and  
REC buttons.  
– 20 –  
 
CONCERT MAGIC  
The great German composer Johann Sebastian Bach once said, “Playing  
the keyboard is simple. Just strike right keys at the right time.” Many  
people wish it were that simple. The reality is very different of course.  
However, there is a way to make playing the keyboard very simple. You  
don’t even have to strike right keys thanks to Concert Magic.  
With Concert Magic, absolutely anyone can sit at the CP piano and make  
real music… even if you’ve never taken a piano lesson in your life.  
To enjoy performing by yourself, you have only to select your favorite  
piece from 40 preprogrammed songs and tap any of the 88 keys with a  
steady rhythm and tempo. Concert Magic will provide the correct melody  
and accompaniment notes, regardless of which keys you press. Anybody,  
young or old, can enjoy Concert Magic from the moment they sit down at  
the CP piano.  
Now let’s see how Concert Magic works.  
1.SELECTING A SONG  
The 40 Concert Magic songs are assigned to each of the 40 white keys,  
classified in six groups by song category such as Children’s Songs,  
American Classics, Christmas Songs.  
All of the song titles are listed on page 33.  
To select a song, press the key to which your desired song is assigned  
while holding down the CONCERT MAGIC button.  
1 2 3  
8
4 5 6 7  
2.LISTENING TO THE SONG  
If you have selected a song you are familiar with, you may want to play by  
yourself right away. However you may want to listen to the song first  
before playing it.  
To listen, press the PLAY/STOPbutton. The CP piano will start playing  
back the selected song. When the demo song is finished, press the START/  
STOP button again to stop. Otherwise the CP piano will play all the other  
Concert Magic songs one at a time in order.  
If you want to listen to a different song, repeat the same procedure to select  
a song.  
– 21 –  
 
3.PERFORMING A SONG  
Now you’re ready to play yourself.  
Tap out the rhythm of the selected song on any one of the 88 black or  
white keys on your piano keyboard. As you tap harder, the notes will  
get louder; as you tap softer, the notes will get quieter. As you tap faster,  
the notes speed up; as you tap slower, they will slow down correspondingly,  
just like regular piano playing.  
Isn’t it fun? You can sound like you’ve been playing for years just by  
pressing one key with one finger.  
Concert Magic is a perfect method for small children to learn music,  
especially to develop a sense of rhythm. For older people who may think  
it is too late to learn the keyboard, Concert Magic is a good first step for  
them to begin with. With Concert Magic, your CP piano can be enjoyed  
by anyone in the family, even those who have never touched a musical  
instrument in their life.  
4.CONCERT MAGIC SONG ARRANGEMENT TYPES  
After playing for a while with Concert Magic you may think that it’s too  
easy and there is very little to learn.  
While it is true that some of the songs are very easy to play, even for  
beginners, there are also some which will challenge you and require some  
practice to play beautifully. Each of the 40 Concert Magic songs falls into  
one of three different categories depending on the skill level required to  
perform them.  
Easy Beat  
These are the easiest songs to play. To perform them, simply tap out a  
constant steady beat on any key on your piano keyboard.  
Look at the following example, “Für Elise”. Press the key with a steady  
sixteenth note rhythm.  
Key on  
x x x x x x  
x x x  
x
x x  
x
x
x
x
x x  
3
#œ #œ  
nxœ x  
j
œ
œ
œ
œ
Œ
œ
œ
œ
#œ  
œ
œ
œ
œ
œ
& 8  
? 3  
#œ  
œ
J
œ
œ
œ
œ
≈ ‰  
≈ ‰  
8
– 22 –  
 
Melody Play  
These songs are also quite easy to play, especially if they are familiar to  
you. To perform them, tap out the rhythm of the melody on any one of the  
keys on your piano keyboard. Singing along as you tap the rhythm can be  
helpful.  
Key on  
x
x
x
x
x
x
x
x
x
x
x
x
x
x
c
c
œ œ  
&
œ œ  
˙
˙
œ œ  
œ œ  
œ œ  
œ œ  
˙
œ œ ˙  
œ
œ
œ
˙
œ
œ
œ
˙
œ
˙
˙
˙
˙
˙
œ ˙  
?
&
˙
˙
˙
˙
˙
˙
˙
˙
˙
Œ
˙
œ
œ
œ
œ
œ
˙
˙
Play “Twinkle, Twinkle, Little Star” for example. Follow the melody’s  
rhythm as shown.  
When performing fast songs with Concert Magic, it is sometimes easier to  
tap two different keys with two fingers alternating. This allows you to  
play twice as fast as you can using only one finger on one key.  
Skillful  
These songs range in difficulty from moderately difficult to difficult. To  
perform them, tap out the rhythm of both the melody and the  
accompaniment notes on any of the keys on your piano keyboard, like  
“Waltz of The Flowers” shown below.  
Key on  
x
x
x
x
x
x
x
x
x
x
x
x
x
#
3
4
#
.
&
˙
œ
œ
œ
œ ˙.  
˙.  
œ
œ
œ œ œ  
œ
œ
œ œ  
œ œ  
œ œ  
œ œ œ  
bœ œ œ  
œ œ œ  
œ œ  
œ
œ
œ
œ
? # 3 œ œ œ  
œ
œ
œ
œ
œ
#
4
œ
œ
œ
It may take some practice to get them just right. A good way to learn these  
songs is to listen to them first, and then try to tap out the rhythms that you  
hear.  
In the song list on page 33, the arrangement type is marked next to each  
song title as “EB” for Easy Beat, “MP” for Melody Play and “SK” for  
Skillful.  
– 23 –  
 
5. Concert Magic Song Demo  
There are three ways to listen to the Concert Magic songs in the  
DEMO mode.  
All Play  
Press the CONCERT MAGIC button and then press the PLAY/  
STOP button without selecting a song. The CP piano will play  
back all of the Concert Magic songs in order.  
Random Play  
Press the CONCERT MAGIC button and then press the DEMO  
button. The CP piano will play back all of the Concert Magic songs  
in random order.  
Category Play  
Press the piano key to which the desired song is assigned while  
holding down the DEMO buttons. The CP piano will play back  
the selected song and, then play the rest of the songs in the same  
song category one after another.  
To stop the demo, press the PLAY/STOP button.  
– 24 –  
 
FUNCTION MODE  
The Function Mode gives you access to many other useful features on  
your CP piano. To enter the Function Mode, press the TOUCH and  
TRANSPOSE buttons at the same time. The LEDs for both buttons  
will flash. Press one of the following sound buttons to choose a function  
to edit. To exit the Function Mode, press either the TOUCH button or  
TRANSPOSE button.  
The following functions can be selected in the Function Mode:  
Tuning (PIANO button)  
Temperament (E. PIANO button)  
MIDI Channel (HARPSI & MALLET button)  
Transmit Program Change On/Off (ORGAN button)  
Local Control On/Off (STRING button)  
Channel Mute (VOCAL & SYNTH button)  
Program Change Number (BRASS & W.WIND button)  
1. TUNING  
This function allows you to adjust the piano’s pitch. You may need to  
adjust the tuning when you play with other instruments or recordings.  
Press the PIANO button while in the function mode. The LED display  
shows you a number that represents the pitch for “A” in Hz (Hertz).  
The range of adjustment is from 427.0 to 453.0 Hz (displayed as 27.0–  
53.0). The factory preset value is set to the modern standardA= 440.0  
Hz (displayed as 40.0).  
Pitch:  
440.0 Hz  
Use the VALUE buttons to raise or lower the pitch.  
2. TEMPERAMENT  
The CP piano offers not only equal temperament (the modern standard)  
but also immediate access to temperaments popular during the Renaissance  
and Baroque periods. It should be interesting and educational to try some  
of the different temperaments, although the equal temperament is dominant  
today.  
Press the E. PIANO button while in the function mode. The LED display  
shows you an abbreviation for the type of temperament currently selected.  
Use the VALUE buttons to select your desired temperament.  
Temperament  
(Equal)  
After you have selected the desired temperament, you must select a key  
signature for the temperament. Limitless modulation of the key became  
available only after the invention of Equal temperament. When we use a  
temperament other than Equal temperament, we must carefully choose the  
key signature to play in.  
– 25 –  
 
To select the key signature of the temperament, simply press one of  
the 88 piano keys. The LED display shows you the note name for the key  
you pressed and it will be chosen as the key of the temperament. For  
example, if the song you are going to play is written in D major, press any  
“D” key to set the temperament key.  
Key in D  
Key in A#  
BRIEF EXPLANATION OF TEMPERAMENTS  
EQUAL TEMPERAMENT (PIANO ONLY)  
Equal(P.only)  
This is the default temperament. If a piano sound is selected the tuning is  
stretched like an acoustic piano (EQUALTEMPERAMENT). If any other  
type of sound is selected the tuning will be EQUAL(FLAT). An explantion  
of EQUAL TEMPERAMENT and EQUALTEMPERAMENT (FLAT) is  
provided later in this section.  
NOTE:  
If a piano sound is used in a layer with any other sound then both sounds  
will use the EQUAL TEMPERAMENT (Stretched) tuning.  
MERSENNE PURE TEMPERAMENT(Major)  
MERSENNE PURE TEMPERAMENT(Minor)  
Pure(Major)  
Pure(minor)  
This temperament, which eliminates dissonances for thirds and fifths is  
still popular for choral music because of its perfect harmony.  
You need to be aware what key you are playing in with this temperament.  
Any key modulation will result in dissonances. When you play music in a  
particular key, you need to match the key of the temperament as well.  
When playing in a major key select Pure (Major) and when playing in a  
minor key select Pure (minor).  
PYTHAGOREAN TEMPERAMENT  
This temperament, which uses mathematical ratios to eliminate dissonance  
for fifths, is very limited for use with chords, but it produces very  
characteristic melodic lines.  
Pythagorean  
Meantone  
MEANTONE TEMPERAMENT  
This temperament, which uses a mean between a major and minor whole  
tone to eliminate dissonance for thirds, was devised to eliminate the lack  
of consonances experienced with certain fifths for the Mersenne pure  
temperament. It produces chords that are more beautiful than those with  
the equal temperament.  
– 26 –  
 
WERCKMEISTER III TEMPERAMENT,  
KIRNBERGER III TEMPERAMENT  
Werckmeister  
Kirnberger  
These two temperaments are placed in between Meantone and Pythagorean.  
For music with few accidentals, this temperament produces the beautiful  
chords of the mean tone, but as accidentals increase, the temperament  
produces the characteristic melodies of the Pythagorean temperament. It  
is used primarily for classical music written in the Baroque era to revive  
the original characteristics.  
EQUAL TEMPERAMENT(FLAT)  
This is “unstretched” equal temperament that divides the scale into twelve  
equal semitones. This produces the same chordal intervals in all twelve  
keys, and has the advantage of limitless modulation of the key. However  
the tonality of each key becomes less characteristic and no chord is in pure  
consonance.  
Equal(Flat)  
EQUAL TEMPERAMENT  
This is the most popular piano temperament. The hearing ability of a  
human is uneven and is not as accurate with high frequency and low  
frequency as it is with the middle range. This temperament’s tuning is  
stretched to compensate for this so the sound will be heard naturally to the  
ears. This “Stretched” equal temperament is a practical variation of the  
“unstretched” equal temperament which was invented on a mathematical  
basis.  
Equal  
3. MIDI CHANNEL  
This function determines on which channel the CP piano will exchange  
MIDI data with an external MIDI device or personal computer.  
Press the HARPSI & MALLET button while in the function mode.  
The LED display shows you the currently selected channel number. The  
default channel is 1.  
Use the VALUE buttons to select your desired MIDI channel, 1-16.  
When the power is first turned on, the CP piano always selects channel 1.  
Channel 15  
– 27 –  
 
4. TRANSMIT PROGRAM CHANGE ON/OFF  
This function determines whether or not the CP piano will transmit program  
change information when pressing the SOUND SELECT buttons. When  
this is turned on, pressing the SOUND SELECT buttons will send the  
program change numbers.  
Press the ORGAN button while in the function mode.  
The display alternatively shows “PGM” (= Program) and on/off status.  
The default is on.  
Use the VALUE buttons to toggle on and off.  
5. LOCAL CONTROL ON/OFF  
This function determines whether the CP piano’s sound will be played  
from the piano’s keyboard (“On”) or only from an external MIDI instrument  
(“Off”).  
Even with local control “Off” the piano’s keyboard will still transmit to an  
external MIDI instrument or personal computer.  
Press the STRING button while in the function mode. The LED display  
shows you “On” or “Off”. The initial value is “On”.  
Local Control  
ON  
Use the VALUE buttons to turn local control “On” and “Off”  
Local Control  
OFF  
6. CHANNEL MUTE  
This function determines which MIDI channels are activated to receive  
MIDI information. You can activate or deactivate each of the 16 channels  
individually.  
Press the VOCAL & SYNTH button while in the function mode. The  
display alternatively shows “P1” (=Play 1) and “On”. This means channel  
1 is activated.  
Use the VALUE buttons to toggle on and off.  
To turn on and off the other channels, use the 16 leftmost white keys to  
select a desired channel. The display will show “P 1” through “P 16”.  
Then use the VALUE buttons to turn them on and off.  
– 28 –  
 
7. SENDING PROGRAM CHANGE NUMBERS  
This function allows the CP piano to transmit program change numbers  
beyond the 24 pre-defined numbers transmitted by the sound select buttons.  
Using this function, you can send any number from 1 to 128.  
Press the BRASS & W. WIND button while in the function mode.  
The display alternatively shows “PG#” (=Program#) and a program change  
number. Use the VALUE buttons to change the number.  
To send the program change number, press both VALUE buttons  
simultaneously.  
– 29 –  
 
MIDI  
The term MIDI is an acronym for Musical Instrument Digital Interface, an  
international standard for connecting synthesizers, sequencers (digital  
recorders) and other electronic instruments so that they can exchange  
performance data.  
The CP67 is equipped with two MIDI jacks for exchanging data: MIDI IN  
and MIDI OUT. Each uses a special cable with a DIN connector.  
MIDI IN : For receiving note, program change and other data.  
MIDI OUT : For sending note, program change and other data.  
MIDI EXAMPLES  
(1) Connection to another MIDI compatible keyboard or sound  
generator module  
When connected as shown in the illustration, data on how the digital piano  
is played (which keys are struck) can be sent to another MIDI instrument.  
Plus, the sound from the CP67 can be layered over the sound of the other  
instrument.  
CP67  
MIDI IN  
MIDI  
OUT  
IN  
Digital Synthesizer  
MIDI cable  
CP67's Piano sound  
Synthesizer's String sound  
– 30 –  
 
(2) Connection to an external sequencer  
When connected as shown in the illustration, you can record songs played  
on the CP67 with a sequencer, and use the CP67’s tones controlled by the  
CP67’s MULTI-TIMBRAL MODE function (which is ON at all times) to  
create a multi-layer MIDI recording.  
CP67  
MIDI  
MIDI OUT  
OUT  
IN  
MIDI IN  
MIDI cable  
MIDI Sequencer  
– 31 –  
 
LIST OF PRESET SOUND  
PIANO  
E. PIANO  
1. Concert Grand  
2. Studio Grand  
3. Honky Tonk Piano  
HARPSI & MALLET  
1. Vibes  
1. Classic E. Piano  
2. Modern E. Piano  
3. 60's E. Piano  
ORGAN  
1. Jazz Organ  
2. Harpsichord  
3. Music Box  
STRING  
1. String Ensemble  
2. Slow Strings  
3. Violin  
BRASS & W.WIND  
1. Solo Trumpet  
2. Flute  
2. Drawbar Organ  
3. Church Organ  
VOCAL & SYNTH  
1. Choir Ahs  
2. New Age Pad  
3. Atmosphere  
SPECIALTY  
1. Nylon Acoustic Guitar  
2. Accordion  
3. Clarinet  
3. Banjo  
STYLE LIST  
BIG BAND  
SWING  
50'S 1  
50'S 2  
60'S 1  
60'S 2  
LATIN  
POP  
BALLAD  
MARCH  
COUNTRY 1  
COUNTRY 2  
WALTZ 1  
WALTZ 2  
C. PIANO (CLASSIC PIANO)  
BROADWAY  
– 32 –  
 
CONCERT MAGIC SONG LIST  
Category  
#
Song Title  
Arrangement  
Type  
Children's Songs  
1
2
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
Twinkle, Twinkle, Little Star  
I'm A Little Teapot  
Mary Had A Little Lamb  
London Bridge  
Row, Row, Row Your Boat  
Frère Jaques  
Old MacDonald Had A Farm  
Hark The Herald Angels Sing  
Jingle Bells  
MP  
MP  
MP  
MP  
MP  
MP  
MP  
MP  
MP  
MP  
MP  
MP  
MP  
MP  
MP  
MP  
EB  
MP  
MP  
MP  
MP  
EB  
SK  
SK  
MP  
EB  
SK  
SK  
SK  
SK  
SK  
MP  
SK  
SK  
EB  
SK  
SK  
SK  
MP  
EB  
Christmas Songs  
Deck The Halls  
O Come All Ye Faithful  
Joy To The World  
Silent Night  
We Wish You A Merry Christmas  
Battle Hymn Of The Republic  
Yankee Doodle  
Danny Boy  
Clementine  
Auld Lang Syne  
Oh Susanna  
Camptown Races  
When The Saints Go Marching In  
The Entertainer  
William Tell Overture  
Andante (Haydn)  
Für Elise  
Clair De Lune  
Skater's Waltz  
Blue Danube Waltz  
Gavotte (Gossec)  
Waltz Of The Flowers  
Bridal Chorus  
American Classics  
Classical Selections 24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
Special Occations  
Wedding March  
Pomp And Circumstance  
When Irish Eyes Are Smiling  
Chiapenacas  
Santa Lucia  
Funicli Funicla  
International Songs 35  
36  
37  
38  
39  
40  
La Marseillaise  
My Wild Irish Rose  
– 33 –  
 
SPECIFICATIONS  
Keyboard 88 Weighted Keys with Advanced Hammer Action IV  
Touch Type 6 Types (Normal, Light 1/2, Heavy 1/2, Off)  
Max Polyphony 96 Notes  
Sounds 24 (from the panel), total 256 Sounds (GM2)  
Effects  
Chorus (1-4), FB Chorus, Flanger, Delay (1-3), Tremolo, Rotary (1-2)  
Reverb (Small Room, Medium Room, Large Room, Medium Hall, Large  
Hall, Plate)  
Rhythm 16 rhythms with variations, Start/Stop, Intro/Ending, Sync, Fill In,  
ACC, 1-2 Play mode  
Digital Recorder 3 Songs, 2 Tracks, 7,000 Notes  
Other Functions Metronome, Transpose, Tuning, MIDI Functions, 3 Demo Songs, 40  
Concert Magic Songs  
Pedals 3 (Soft, Sostenuto, Sustain)  
Jacks Headphones x 2, Pedal, MIDI (IN, OUT), LINE IN (L, R),  
LINE OUT (L/MONO, R)  
Output Power 16 W x 2  
Speakers  
Power Consumption 50 W  
Dimensions 139 x 47 x 84 (cm)  
Weight 42.5 kg  
16 cm x 2  
Specifications are subject to change without notice.  
DEMO SONG LIST  
1. Rhapsodie No.2 / Brahms  
2. Original  
3. Original  
– 34 –  
 
MIDI IMPLEMENTATION CHART  
KAWAI DIGITAL PIANO  
MODEL: CP67  
Date: December 2005  
Version: 1.0  
FUNCTION  
TRANSMITTED  
RECEIVED  
REMARKS  
Basic Channel  
Mode  
(Default)  
(Changed)  
(Default)  
(Message)  
(Altered)  
1
1-16  
3
1-16  
x
3
x
✻✻✻✻✻✻✻✻  
3, 4  
Note Number  
Velocity  
21-108  
✻✻✻✻✻✻✻✻  
0-127  
0-127  
(True Voice)  
(Note ON)  
(Note OFF)  
O: 9nH v=1-127  
x: 8nH v=0  
O
x
After Touch  
Key’s  
Channel’s  
x
x
x
O
x
x
x
O
x
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
0-127  
O
x
Pitch Bend  
Control Change  
0, 32  
1
Bank Select  
Modulation  
Portament Time  
Data Entry  
Volume  
Panpot  
Expression  
Damper pedal  
Portament  
Sosutenuto pedal  
Soft pedal  
Hold 2  
Resonance  
Release  
Attack  
Cutoff  
Decay  
Vibrato Speed  
Vibrato Depth  
Vibrato Delay  
Portament Control  
Reverb Send Level  
Chorus Send Level  
NRPN LSB/MSB  
RPN LSB/MSB  
5
6, 38  
7
10  
11  
64  
65  
66  
67  
69  
71  
72  
73  
74  
75  
76  
O
x
O (Right pedal)  
x
O (Center pedal)  
O (Left pedal)  
x
x
x
x
x
x
x
x
x
x
O
O
x
x
77  
78  
84  
91  
93  
98, 99  
100, 101  
Program Change  
O
✻✻✻✻✻✻✻✻  
True  
Program No. 1-128  
System Exclusive  
Common (Song Position)  
O
x
(Song Select)  
(Tune)  
System: Real Time (Clock)  
(Commands)  
x
x
O
O
x
x
x
O
O
O
O
O
O
x
Others  
(All Sounds OFF)  
(Reset All Controllers)  
(All Notes OFF)  
(Active Sense)  
x
O
O
x
(Reset)  
Mode 1: OMNI ON, POLY  
Mode 3: OMNI OFF, POLY  
Mode 2: OMNI ON, MONO  
Mode 4: OMNI OFF, MONO  
– 35 –  
 
CP67 Owner's Manual  
OM987E-C0512  
Printed in Indonesia  
 

Intel Computer Hardware 62230ANHMWWB User Manual
Jet Tools Electric Heater J150ECA User Manual
Jura Capresso Coffeemaker IMPRESSA E40 User Manual
Kambrook Hot Beverage Maker KAK5 User Manual
Ken A Vision Microscope Magnifier T 1922 User Manual
Kenmore Dishwasher 58715412100A User Manual
Kenmore Home Security System 790479 User Manual
Kodak Digital Camera 1710722 User Manual
Kodak Digital Camera C713 User Manual
Kompernass Blood Pressure Monitor KH 8099 User Manual